crankpin

crankpin

1. The S1-217 crankpin lathe of crankshaft is one of the important equipment.

2 17曲轴连杆颈车床是车削曲轴连杆颈主要设备之一。

2. For the connecting rod bearing arrangements of combustion engines and compressors, SKF has special needle roller and cage assemblies for gudgeon pin bearing arrangements (fig 4a) and crankpin bearing arrangements (fig 5a).

SKF有用于活塞销轴承配置(图4a)和曲轴销轴承配置(图5a)的特殊滚针和保持架组件,适用于内燃机和压缩机的活塞杆轴承配置。

3. "This terrific push against the piston forces it downward, and a power impulse is transmitted through the connecting rod to the crankpin on the crankshaft.

作用于活塞上强大的推动力推动活塞向下运动,并将这一推力通过连杆传到曲轴上的连杆轴颈上。

4. "This terrific push against the piston forces it downward, and a power impulse is transmitted through the connecting rod to the crankpin on the crankshaft. The crankshaft is rotated as the piston is pushed down by the pressure above it."

作用于活塞上强大的推动力推动活塞向下运动,并将这一推力通过连杆传到曲轴上的连杆轴颈上。因此,当活塞受压向下运动时,推动曲轴转动。

5. The influence of structure parameters which include diameter of round corner in axis, crankpin length and crankweb width and so on to stress focus place were discussed.

同时还探讨了曲轴的部分结构参数对其应力集中部位的影响，如轴颈过渡圆角半径、曲柄销长度和曲柄臂厚度等。

6. Design and Application of Crankpin Turning Fixture of special Balancing Crankshaft

异型配重铁曲轴连杆颈车削夹具的设计与应用

7. The V-arrangement, with two connecting rods attached to each crankpin, permits reducing the engine length by almost one-half, thus making it much more rigid, with a stiff crankshaft.

形排列，由于每个曲柄销上有两根连杆，所以可使发动机的长度几乎缩短一半，这样就使发动机的刚性更大，曲轴也更坚固。这种形式只需要很少的维护工作，安装也方便。

8. The connecting rods of all the pistons work on a single crankpin, which rotates around the center of the circle.

所有的活塞连杆都在同一个曲柄销上工作，绕着圆心旋转。

9. Effects of Speed Increasing and Charge Boosting on the Wear of Crankshaft Journal and Crankpin

提高转速与增压对内燃机主轴颈和曲柄销磨损的影响

10. Wearing of crankshaft journals and crankpin is one of the most key indexes for evaluating the working life of internal combustion engine.

摘要内燃机曲轴轴颈的磨损量是衡量内燃机寿命的一个重要指标。

11. The adjustment method of crankshaft deflection is improved by the means of FEM, in which the infection of gravity and deformation of crankshaft, crankpin and crank web are included.

摘要在考虑曲轴主轴颈、曲柄臂和连杆轴颈的变形以及重力对臂距差影响的基础上，利用有限元分析工具，改进了传统的利用测量臂距差调整曲轴中心轴线的方法。

12. The failure analyses were conducted on a diesel engine crankshaft made of ductile cast iron, which was nitrided.The fracture occurred at the web between the 1st crankpin and 2nd journal.

摘要柴油机氮化球铁曲轴在服役过程中发生了断裂，断裂发生在第一曲拐与第二主轴颈之间的曲柄处。

13. crankpin path

曲柄圆

14. crankpin returning tool

曲柄销修整工具

15. crankpin seat

曲柄销座

16. crankpin bearing lubrication

曲柄销承润滑 连杆轴承润滑

17. Crankpin' s Damage

曲柄销损坏

18. crankpin grease

曲柄销滑脂

19. crankpin roller

曲柄销滚柱

20. crankpin grinder

曲柄销磨床

21. crankpin bush

曲柄销衬套

22. crankpin metal

曲柄销衬套合金

23. crankpin lathe

曲柄销车床

24. crankpin bearing

曲柄销轴承

25. crankpin step

曲柄销轴瓦

26. crankpin load

曲柄销载荷

27. crankpin angle

曲柄销配置角度

28. crankpin brass

曲柄销黄铜衬

29. Keywords Crank;Crankpin;Interpolation algorithm;

曲轴;连杆颈;插补算法;

30. Keywords Crankpin;Grinding;Roundness;Com-pensation;

曲轴连杆颈;磨削;圆度误差;补偿;

31. Keywords Crankpin Lathe;Fixture;Locating;Eccentric Bushing;

曲轴连杆颈车床;夹具;定位;偏心瓦块;

32. Each pair（of cylinders） drives one crankpin, via two connecting rods, and the front of the crankshaft is geared down to a slower-running propeller.

每对气缸通过连杆来驱动一个曲柄销，在曲柄拴的前部是减速到低速运行的螺旋桨。

33. The Load map and wearing maps of the crankshaft journals and crankpin are obtained under various operating conditions.

研究表明：气缸压力和转速升高后，曲柄销和主轴颈的磨损均呈现增加趋势。

34. hollow crankpin

空心连杆轴颈

35. The cap and rod have bearings which permit the crankpin to rotate freely within the rod

轴瓦盖和连杆中有轴瓦，它允许连杆内的曲柄锁自由地转动。

36. crankpin end

连杆大头

37. The connecting rod is attached at one end to a crankpin on the crankshaft and at the other end to a piston, through a piston pin or wrist pin.

连杆的一端与曲轴的连杆轴颈相连，另一端通过活塞销与活塞相连。

38. The connecting rod carries the power thrusts from the piston to the crankpin.

连杆的作用是将活塞承受的压力传给连杆轴颈。

39. bearing cap attaches the connecting rod to the crankpin.

连杆轴瓦盖将连杆安装到曲轴销上。

40. By attaching the connecting rods to a master disk surrounding the crankpin, as many as twelve cylinders have been made to work on a single crankpin.

通过把连杆连接到包住曲柄销的一个主盘上，十二个气缸便可在同一个曲柄销上工作。

41. As the crankshaft rotates, the crankpin swings in a circle around the shaft

随着曲轴的转动，曲柄销绕主轴作圆周摆动。