holddown

holddown

1. IGRP also maintains many timers and variables that contain time intervals. These include an update timer, an invalid timer, a holddown timer, and a flush timer.

IGRP也维护许多计时器和包含时间间隔的变数。这些包括更新计时器、无效计时器、保持计时器和清除计时器。

2. Holddown period

n. 抑制计时时期

3. The default holddown for RIP is 180 seconds.

RIP预设的保持时间为180秒。

4. holddown nut

[化] 压紧螺母

5. Independent and V-type locations and sealing holddown are used in precision locating fixture design, so the fixture structure is simple and easy to operate.

介绍了叶片精密定位夹具在设计时采用的分体式V形定位和密封式压紧方法,使夹具结构简单、操作方便。

6. Holddown timer This sets the amount of time during which routing information is suppressed.

保持失效定时器：用于设置路由信息被抑制的时间值。

7. Holddown timers help prevent counting to infinity but also increase convergence time.

保持计时器可帮忙防止无限计数的问题，但也会增加收歛时间。

8. The holddown timer specifies the amount of time for which information about poorer routes is ignored.

保持计时器指定较差的路由资讯将被忽略的时间总计。

9. The holddown timer is another mechanism that may need to be configured.

保持计时器是另一个可能需要组态设定的机制。

10. holddown clip

压具夹

11. HOLDDOWN CLIP AND PIN

压板夹子和销

12. holddown spring

压紧弹簧

13. holddown plate

压紧盖板

14. Poison reverse updates then are sent to remove the route and place it in holddown.

反向毒害的更新送出后将移除该路由，并使它处于保持状态。

15. The holddown timer can be decreased to speed up convergence but should be done with caution.

可以藉由降低保持计时器之值以加速收歛，但是必须小心。

16. Therefore, the holddown timer should be set to slightly more than 120 seconds.

因此，保持计时器应该设成比120秒还稍大些。

17. holddown groove

固定槽

18. Centerline of the slot at base of distributor is aligned to centerline of distributor holddown bolt hole on enginIn this position, the holddown bolt should easily pass through slot and into engine.

在分电盘基座上槽的中心线应与引擎上分电盘垂下螺栓孔的中心线对准。在这个位置，垂下螺栓应容易地通过槽进入引擎。

19. In Figure , the holddown timer is set to 180 seconds.Therefore, an update to a route that was down and is now up could stay in the holddown state until the full 180 seconds have passed.

在图 中，限制计时器设定为 180 秒，因此对一个原本中断而现在恢复的路由更新可能停留在限制状态内直到经过 180 秒。

20. In a distance vector algorithm, the holddown interval for large or complex networks

在距离向量算法中,大型或复杂

21. crowfoot holddown

将盖子固定在搭板上的叉子

22. How does route poisoning work with holddown timers to prevent routing loops?

带有抑制计时的路由毒化是如何防止路由循环的?

23. spring holddown

弹簧压紧板

24. Keywords drawing die;curved surface holddown;position of drawing rib;

拉伸模;曲面压边;拉伸筋;

25. curved surface holddown

曲面压边

26. The unit horse head polished rod close to beam suspension gravity working point .Therefore, while pump holddown beam bending moment so small that will not cause beam broken.

本机驴头悬点距游梁吊重力作用点距离很短，所以，卡泵时游梁弯矩小，不足以造成折梁。

27. hydraulic holddown

水力压具

28. hydraulic packer holddown

水力封隔器定位器

29. battery holddown

电瓶夹板

30. battery holddown cover

电瓶夹板盖

31. Suddenly, he stopped and holddown his arms.This happy young man didn't wear underlinen!

突然，国王停住了，垂下了双手，这个幸福的人没有穿衬衣！

32. Keywords Precision location;Independent and V-type location;Sealing holddown;

精密定位;分体式V形定位;密封式压紧;