preheating
preheating
1. What is the required minimum preheat and interpass temperature for 1 in. thick API 5L grade B steel welded with flux cored arc welding ?
(对于用药芯电弧焊接厚度为1in的API 5L, B级钢的最小预热及层间温度是多少？
2. Deaerator feed water preheat system (no preheating or heat integration with other plants).
1.除氧器给水预热系统/2.除氧器向水预热系统供水（没有预热或与其它装置的热联合）。
3. Resume by alarm in 24 hours,save the time of preheat.
24小时定时开机，节省预热时间；
4. FXD does not have any free carbon in the preheat flame and does not blow back in the torch.
FXD的预热火焰没有自由碳，不能进行黑色金属之间的焊接。
5. QR-35 Burner is particularly suitable for preheating screed at construction site.
QR-35型燃烧器特别适用于野外施工时对熨平板进行预热。
6. FXD will not weld mild steel to steel because of the absence of free carbon in the preheat flame.
|| 因为缺少自由碳，FXD将不能进行火焰加热的钢与钢的焊接。
7. Only one preheating furnace can suffice all melting furnace's use.
一台预热炉就可以满足所有熔炼炉用料。
8. Condensate from the first-effect calandria is used for preheating the feed .
一效列管换热器中出来的冷凝液被用来预热进料。
9. A certain distance between two inductors must be maintained so that the magnetic field in the preheating inductor has no effect on that in forming inductor for steady shaping.
两感应圈间必须保持一定距离,使预热感应圈的磁场不影响成形感应圈的磁场分布,利于成形稳定;
10. Two seconds, the instrument automatically enter the fifth Kushiro countdown preheating time or reset button to enter the transfer, or test selection.
两秒钟后，仪器自动进入五分钏倒计时预热时间或按复位键进入调零或测试选择状态。
11. An improved voltage-mode cathode preheating is also proposed to enhance the lamp ignition process and upgrade lamp performance during a steady-state operation.
为了提高灯管驱动顺序以及稳态操作的效能，本论文将提出一种改良式的电压预热方法。
12. A scrap preheating model was developed to study the characteristics of scrap preheating in Fuchs finger shaft furnace(FSF) as a sub model of dynamic simulation for FSF.
为了研究烟道竖炉电弧炉中废钢预热的特性,建立了废钢预热模型,此模型是竖炉冶炼动态模拟的一个子模型。模型可以计算,预热废钢入炉温度,为炉内动态模拟提供初始数据;
13. In order to fully utilize the VCM and heat in centrifugal mother liquid, selection on the units for mother liquid sedimentation and air preheating were introduced.
介绍了为充分利用离心母液水中所含的氯乙烯单体和携带的热量而选择的沉降母液和预热空气的设备及回收工艺流程。
14. Preheating unit by using Xiapu gas is introduced, the key point that welding casing can be preheated without getting into furnace has been achieved.
介绍了利用霞普气制作的预热装置,实现了压缩机焊接机壳不需进炉就能预热的关键。
15. The process design for ignition furnace in sintering production to use B.F. gas as the only fuel with preheating technique and its application are introduced.
介绍了石钢烧结生产以高炉煤气为单一燃料,应用预热技术完成点火炉的工艺设计和生产使用效果。
16. Based on the design and motion parameter,the economic benefit of heat pipe transducer preheating combustion supporting gas in hot blast stoves of BF are analysed.
从设计参数以及运行参数出发,分析在高炉热风炉上应用热管换热器预热助燃空气和煤气所取得的经济效益。
17. Hot cathode lamp designed to start with preheating of the electrodes - for example: 'TL'M 'TL'RS lamp.
以预热电极方式来启动的热阴极光源。
18. First to preheat or frozen!
先预热或冷藏一下！
19. Place the tile on the bottom rack in the oven, and preheat your oven while you make your dough and assemble the toppings.
准备好所需配料，并在做生面团之前把烤炉加热。
20. Effect of preheat, smaller focus spot and welding processing parameter on sensitivity to cracking is studied.
分析了激光焊接时为克服焊接裂纹所采取的焊前预热、短焦距焊接及焊接工艺参数等因素对裂纹敏感性的影响。
21. Reasonable temperature requirement and its controlling measures in the course of green pellet drying,preheating and oxidizing in grate are analyzed.
分析了生球的在链箅机内进行干燥、预热及氧化的各段合理温度要求、调节温度故障的措施和有效预防破坏性高温停机的对策;
22. An antifreezing ventilation system at winter in a gold mine is designed by use of the earth temperature preheating technology.
利用地温预热入风流技术,设计了金厂沟梁金矿冬季防冻通风系统。
23. Abstract： An antifreezing ventilation system at winter in a gold mine is designed by use of the earth temperature preheating technology.
利用地温预热入风流技术，设计了金厂沟梁金矿冬季防冻通风系统。
24. The technique of preheating raw meal and separating combustion has shown its remarkable effect in reducing NOx and SO2 emissions, but should be completed further for the indus- trial use.
利用热生料和分级燃烧技术减少 NOx 和 SO_2的排放量已取得了明显的效果,今后将进一步完善达到实用的程度。
25. To make toasts: Prepare grill or preheat broiler.
制作烤面包片：准备烤架或预热烤焙用具。
26. Production: preheat oven to170° C, while preheating, butter and100 grams of sugar Spinning Mixing lighter milky white.
制作：预热烤箱到170℃预热的同时，把奶油与100克细纱糖混合搅拌呈淡乳白色。
27. Frame of the heating furnace like beer pasteurism sterilizer.Have an aluminium ingot preheat box.The box's length is near half a burdening span.
加热炉结构类似啤酒杀菌机，有一个铝锭预热箱，预热箱长度接近半个配料跨。
28. Because of its super size and high strength, during fitting and welding after preheating, splaying crack in the penstocks occurred .
压力钢管因尺寸超大、刚度强,预热装配和焊接过程中出现焊缝张开及缺陷严重超标的现象。
29. Because of its super size and high strength, during fitting and welding after preheating, splaying crack in the penstocks occurred.
压力钢管因尺寸超大、刚度强，预热装配和焊接过程中出现焊缝张开及缺陷严重超标的现象。
30. After the engine start, power off, and then the preheating plug's oil way will close automatically.
发动机启动完成后关闭电源，预热塞油路亦自动关闭；
31. Steve: Can you preheat the oven to180 Celsius please? I'm about to bake the cake.
史提夫:你能帮我把烤箱预热到180度吗?我准备要烤蛋糕了.
32. Due to higher melting point and soldering temperature for lead-free solders, a longer preheating time is required to ensure the PCB is properly preheated.
因为无铅焊料的熔点较高，焊接温度很高，因此需要较长的预热时间，使PCB吸收足够热量，为焊接作好准备。
33. In "The campus visiting" the earlier period, propagandizes and conducts the correlation with emphasis the preheating course.
在“校园访问”前期，重点宣传并举办相关的预热讲座。
34. In the compression moulding technology, preheat and prepressing procedures are added to improve the flowability of the bond and physical and mechanical properties of the product.
在压缩模塑工艺中，增加预热、预压工序，提高粘合剂的流动性和产品的物理机械性能。
35. The standard furnace utilizes the supercharge preheating technique where the waste gases, being exhausted over the top of the crucible, preheat the solid charge.
在坩埚的顶端排出废气，预热装料处，这种标准炉采用了加压预热技术。
36. In this piece of propaganda earlier period, resurfaces by Wang Fei does preheating, this tenth media chase focal point.
在该片宣传前期，以王菲的复出做预热，这成了媒体追逐的焦点。
37. The CFL electronic ballast based on electronic driver VK05CFL can realize preheating function,end of life(EOL)protection,lamp presence detection and automatic restart.
基于电子驱动器VK05CFL的CFL电子镇流器可以实现预热、灯寿终保护、灯存在检测和自动重启等功能。
38. Before laminating, the substrate is preheated by a preheat roll.The laminating cooling roll adopts a forced cooling structure and tow station auto-friction rewinding devices.
复合前采用预热对基材进行预热烘干，复膜冷辊采用强迫冷却结构，双工位表面摩擦自动卷取装置。
39. Ok. By the way, did you preheat the oven already? According to this recipe, you need to preheat the oven to 350 degrees.
好了。对了,你已经预熟烤箱了吗?照这个食谱看来,你必须先把烤箱预熟到华氏350度。
40. The different methods which calculate the preheat temperature are compared,the CET? method is most accurate.
对F/B复相钢采用cet公式预测止裂温度较为准确。
41. This paper summarizes the research results related to scale formation in the operations, especially in pulp preheating and temperature rising, of the Bayer process.
对有关拜耳法过程中特别是矿浆预热升温过程中结疤问题的研究成果进行了综述。
42. Controlling the preheating temperature for fuel oil of heat Medium heater is a key to increase the efficiency and stable operation of heater,also a way to save energy and reduce loss.
对热媒炉燃料油预热温度的控制是热媒炉提高炉效、稳定运行的关键,也是节能降耗的有效途径。
43. The designing parameters of the coal mines ventilating and preheating are discussed.Some experiences on the chosen types and application of the preheating epuipment is introduced.
对矿井进风预热设计参数进行了探讨,并介绍了预热设备的选型和应用中的一些经验。
44. Leave away the sepal and crash the petal parts. Preheat the oven to 175C/350F.
将干燥玫瑰花去掉花萼，以手捏碎花瓣部份。烤箱预热至175C/350F。
45. Sand Shell Preheat: Heat the sand shell in order to strengthen the shell.
将模壳放置焙烧炉中焙烧以增加其强度。
46. Preheat oven to 350 degrees. In a large bowl, mix together oats, almonds, pumpkin seeds, brown sugar, cinnamon and salt.
将烤箱预热到350度。然后将燕麦，杏仁，南瓜子，红糖，桂皮和盐放入一个大碗内进行混合；
47. Preheat the oven to gas Mark 6.
将烤箱预热到6挡。
48. Form the dough into about 12 round or oval rolls and set them on a greased baking sheet. Let rise for about 0 minutes. Preheat the oven to 200C/400F.
将面团分成12等份，揉成椭圆或是圆状，放到抹了油的烤纸上发酵大约10分钟。预热烤箱到200C/400F。
49. The influence of the preheating and the cooling water pipe on temperature gradient of the die has also been analyzed with this ADINA.
并利用ADINA软件分析了冷却水管的作用以及预热对模具温度梯度的影响。
50. When there are no codes governing the welding, one must determine whether preheat is required, and if so, what preheat temperature will be appropriate.
当不存在码管焊接时，我们必须确定是否预热需要，如果是的话，什么预热温度，将是适当的做法。
51. Preheat a grill griddle. Season the flank steak with salt and pepper, grill to medium-rare for approximately 8 minutes.
扒炉烧热，另牛腹扒取出撒上盐及胡椒粉调味，然后每边烤约8分钟至3成熟。
52. Preheat the oven about 180degree .
把焗炉预热至180度。
53. Preheat the spoons in a steamer, then fill the spoons with rice flour batter and steam over high heat for 4 minutes, then serve with the toppings.
把汤匙放在蒸锅中先蒸热，然后把粉浆倾入汤匙中，以猛火蒸4分钟后取出，放上配料即成。
54. Preheat oven to450°. In a medium bowl, combine chicken, celery, tomatoes, zucchini, raisins, parsley, and mint, and set aside.
把烤箱提前加热到450度。将鸡肉、菜、茄、瓜、萄干、芹以及薄荷放在一个中碗里，备用。
55. Preheat an oven to 425°F. Brush an 8 1?2-inch tapas pan with 2 Tbs. of the clarified butter.
把烤箱预热到425华氏度,在81/2英寸的西班牙式小铁锅上刷2汤匙的溶解黄油.
56. Preheat the iron to over 200C (Do not use the steam function) and iron on the above greaseproof paper for 1 minute only, look at the watch / clock to count the time!
把熨斗预热到超过200C(不要使用蒸气)，根据说明书，把熨斗放在牛油上约1分钟，用手表或钟计时!
57. Drain the pineapple and reserve the juice for the later use. Preheat the oven to 200C/390F.
把罐头菠萝沥干，菠萝汁备用。预热烤箱到200C/390F。
58. Trim any excess skin and fat from the chicken pieces. Preheat the oil in a deep-fryer to 350 degrees.
把鸡肉片里的多余的鸡皮和脂肪除去。将油在一个深底煎锅里预热到350度。
59. Combine together matcha tea powder and hot water in a bowl. Melt chocolate over a hot-water bath. Preheat the oven to 175C/350F.
抹茶粉用热水调匀备用。座热水融化巧克力。烤箱预热到175C/350F。
60. The results show that the excess air inleakage within the fumace occurred in the preheat sections and high exhaust gas temperature will increase the furnace fuel consumption.
指出促使焙烧时热耗增大的主要原因是预热段空气的严重渗漏以及排烟温度的过高。
61. According to this require, it is necessary that we mount an aluminium ingot preheating furnace.
按照这一要求，我们公司有必要上一台铝锭预热炉。
62. The influences of coating material, preheating temperature, spray parameters, thickness of bond coatings and postheating treatment on the coating properties were examined.
探讨了涂层材料、预热温度、喷涂工艺参数、中间过渡层厚度及后续热处理温度等对涂层结合性能和抗热冲击疲劳性能的影响规律。
63. The designing keys of the regenerative ladle preheating system are tried to find out in the paper.They are significant for engineering design.
探讨了蓄热式钢包烘考器的设计关键,对工程设计具有一定的指导意义。
64. The elastic recovery of molding products was reduced and the molding accuracy in size of products was improved through increasing the preheating temperature of stock and the pressure holding time.
提高坯料预热温度和(或)保压时间,可使模压制品的弹性回复明显减小、成型尺寸精度显著提高。
65. Abstract： This paper introduces the application effects of air cooling and preheating and standard tuyere brich as well as double air box tornado on the cupola.
摘 要： 介绍了空冷、预热、标准化风口砖及双风箱龙卷风供风在冲天炉上应用的效果；
66. Preheating Block is made of Aluminium powder, ferric iron powder, arenaceous quartz, and binder, and it can release great heat quickly after sparked.
摘要预热块由铝粉、氧化铁粉、石英砂及粘结剂制成，点燃后可以在短时间释放大量热量；
67. Preheating is an important technology in Selective Laser Sintering (SLS).
摘要预热是选区激光烧结成型工艺的重要部分。
68. Preheat a grill, place the beef skewers on the grill and cook until they are done, turning occasionally during grilling. Serve hot with the satay sauce.
放在已预热的烤炉上烧烤，偶尔反转两面烧，烤熟后蘸沙嗲酱同吃。
69. Abstract: An antifreezing ventilation system at winter in a gold mine is designed by use of the earth temperature preheating technology.
文摘:利用地温预热入风流技术，设计了金厂沟梁金矿冬季防冻通风系统。
70. This paper briefly describes the new shaft type scrap preheating system called UL BA developed by Japanese Nippon Steel Corporation.
文章简要介绍了日本新日铁开发的新型竖炉式废钢预热系统,即:UL-BA方式预热装置。
71. For new dry cement process,size distributions of raw meal alter as degree of decarbonation change,in the process of preheating and precalcing.
新型干法水泥生产在预热和预分解过程中，随着生料分解率的变化其粒度分布也会产生变化。
72. To meet special requirement in construction, do pipeline clearing and preheating after pressure test and trial operation.
施工中的特殊要求,试压后的清管预热及投油试运等。
73. It's the most economical choice of preheating the base board bard before cutting.
是冲切前基板预热最经济之选择。
74. Preheat and oil wok with 1 tbsp of oil. Add in beef and fry briefly. Add in vermicelli and fry till cooked.
最后下调味料将牛肉及粉丝兜匀，盛于椰菜上，即可享用。
75. There was some discussion of electron weapon beams, through the use of a laser beam to preheat a path for the following electron beam.
有一些对于通过激光束为接下来的电子束预先加热一条通道的电子武器束的讨论。
76. Various technical modification items, such as secondary mixing drum,muticyclone,preheating manner of mixture,single-roll crusher, loosener etc,in the major repair of sinter plant , Panzhihua I&S Co.
本文介绍攀钢炼铁厂1号烧结机大修对烧结机系统进行的多项技术改造，包括：二次混合机、多管除尘器、混合料预热方式、单辊破碎机、松料器等。
77. This article describes the composition of scrap preheating (with waste fume of the EAF) and dedusting system of Zhujiang 150t EAF, the selection of equipment and their functions.
本文对珠江钢厂150t电炉烟气废钢预热及除尘系统组成、设备选择及功能说明等进行了综述。
78. This paper has proved that the roll preheat temperature and rise velocity of inductors has influence which is not to be overlook on the output power and current of inductors.
本文用大量生产记录和试验数据证明,轧辊预热温度和感应器上升速度对感应器输出功率和电流有不可忽视的影响。
79. A set of absorption heat pump is designed to recycle these heat for preheating brine and reduce the steam consumption.
本文的目的是设计一套吸收式热泵回收这部分热量,用来预热盐水,达到降低蒸汽消耗的目的。
80. The processes of preheating and welding of super scale penstocks were detailed.
本文详细叙述了巨型压力钢管的预热装配和焊接过程。
